Searched refs:flags (Results 1 – 25 of 119) sorted by relevance
12345
| /dts/upstream/Bindings/thermal/ |
| A D | spear-thermal.txt | 6 - st,thermal-flags: flags used to enable thermal sensor
13 st,thermal-flags = <0x7000>;
|
| /dts/upstream/Bindings/rtc/ |
| A D | moxa,moxart-rtc.txt | 6 - rtc-sclk-gpios : RTC sclk gpio, with zero flags
7 - rtc-data-gpios : RTC data gpio, with zero flags
8 - rtc-reset-gpios : RTC reset gpio, with zero flags
|
| A D | rtc-st-lpc.txt | 14 - interrupts : LPC interrupt line number and associated flags
|
| /dts/upstream/Bindings/gpio/ |
| A D | nxp,lpc3220-gpio.yaml | 32 3) flags:
49 #gpio-cells = <3>; /* bank, pin, flags */
|
| A D | cdns,gpio.txt | 8 * second cell specifies the GPIO flags, as defined in
10 and GPIO_ACTIVE_LOW flags are supported.
|
| A D | brcm,brcmstb-gpio.yaml | 55 flags. The following subset of flags is supported:
56 - bits[3:0] trigger type and level flags
|
| A D | gpio-altera.txt | 14 - The second cell is the interrupt trigger type and level flags.
21 Only the following flags are supported:
|
| A D | spacemit,k1-gpio.yaml | 60 support level interrupts, so flags of IRQ_TYPE_LEVEL_HIGH,
62 Refer <dt-bindings/interrupt-controller/irq.h> for valid flags.
|
| A D | nvidia,tegra20-gpio.yaml | 48 used to specify flags:
50 bits[3:0] trigger type and level flags:
|
| A D | gpio-thunderx.txt | 16 - Second cell is triggering flags as defined in interrupts.txt.
|
| A D | x-powers,axp209-gpio.yaml | 16 The first cell is the pin number and the second is the GPIO flags.
|
| /dts/upstream/Bindings/mfd/ |
| A D | palmas.txt | 24 - #interrupt-cells : should be set to 2 for IRQ number and flags
26 The second cell is the flags, encoded as the trigger masks from
|
| A D | tps65912.txt | 10 The second cell is the flags, encoded as trigger
14 the second cell is used to specify flags.
|
| A D | altera-a10sr.txt | 12 The second cell is the flags, encoded as trigger
27 the second cell is used to specify flags.
|
| A D | tc3589x.txt | 32 TC3589x GPIO interrupt controller, the second cell is the interrupt flags
34 flags are valid:
42 GPIO controller, the second cell is the flags.
|
| A D | ti,tps65086.yaml | 28 The first cell is the IRQ number. The second cell is the flags,
37 flags. See ../gpio/gpio.txt for more information.
|
| /dts/upstream/Bindings/interrupt-controller/ |
| A D | atmel,aic.yaml | 37 The 2nd cell specifies flags:
38 bits[3:0] trigger type and level flags:
|
| /dts/upstream/Bindings/mailbox/ |
| A D | nvidia,tegra186-hsp.yaml | 31 A bit mask of flags that further specifies the type of shared
43 A bit mask of flags that further specify how the shared mailbox
44 will be used. Valid flags are:
|
| /dts/upstream/Bindings/mmc/ |
| A D | sdhci-spear.txt | 10 - cd-gpios: card detect gpio, with zero flags.
|
| /dts/upstream/Bindings/powerpc/opal/ |
| A D | power-mgt.txt | 14 - flags: indicating some aspects of this idle states such as the
33 "ibm,cpu-idle-state-names" and "ibm,cpu-idle-state-flags" are
40 - ibm,cpu-idle-state-flags:
42 flags associated with the aforementioned idle-states. The
|
| /dts/upstream/Bindings/pwm/ |
| A D | pwm.yaml | 22 optionally a number of flags (defined in <dt-bindings/pwm/pwm.h>).
|
| /dts/upstream/Bindings/timer/ |
| A D | st,stih407-lpc | 14 - interrupts : LPC interrupt line number and associated flags
|
| A D | faraday,fttmr010.txt | 18 flags for falling edge
|
| /dts/upstream/Bindings/watchdog/ |
| A D | nuvoton,npcm-wdt.txt | 12 - interrupts : Contain the timer interrupt with flags for
|
| /dts/upstream/include/dt-bindings/usb/ |
| A D | pd.h | 32 #define PDO_FIXED(mv, ma, flags) \ argument
33 (PDO_TYPE(PDO_TYPE_FIXED) | (flags) | \
|
Completed in 38 milliseconds
12345