1 /* SPDX-License-Identifier: GPL-2.0+ */ 2 /* 3 * Copyright 2020-2021 NXP 4 * Copyright 2016 Freescale Semiconductor, Inc. 5 */ 6 7 #ifndef __LS1012ARDB_H__ 8 #define __LS1012ARDB_H__ 9 10 #include "ls1012a_common.h" 11 12 /* DDR */ 13 #define CFG_SYS_SDRAM_SIZE 0x40000000 14 15 /* 16 * I2C IO expander 17 */ 18 19 #define I2C_MUX_IO_ADDR 0x24 20 #define I2C_MUX_IO2_ADDR 0x25 21 #define I2C_MUX_IO_0 0 22 #define I2C_MUX_IO_1 1 23 #define SW_BOOT_MASK 0x03 24 #define SW_BOOT_EMU 0x02 25 #define SW_BOOT_BANK1 0x00 26 #define SW_BOOT_BANK2 0x01 27 #define SW_REV_MASK 0xF8 28 #define SW_REV_A 0xF8 29 #define SW_REV_B 0xF0 30 #define SW_REV_C 0xE8 31 #define SW_REV_C1 0xE0 32 #define SW_REV_C2 0xD8 33 #define SW_REV_D 0xD0 34 #define SW_REV_E 0xC8 35 #define __PHY_MASK 0xF9 36 #define __PHY_ETH2_MASK 0xFB 37 #define __PHY_ETH1_MASK 0xFD 38 39 #undef CFG_EXTRA_ENV_SETTINGS 40 #define CFG_EXTRA_ENV_SETTINGS \ 41 "verify=no\0" \ 42 "initrd_high=0xffffffffffffffff\0" \ 43 "kernel_addr=0x01000000\0" \ 44 "kernelheader_addr=0x600000\0" \ 45 "scriptaddr=0x80000000\0" \ 46 "scripthdraddr=0x80080000\0" \ 47 "fdtheader_addr_r=0x80100000\0" \ 48 "kernelheader_addr_r=0x80200000\0" \ 49 "kernel_addr_r=0x96000000\0" \ 50 "fdt_addr_r=0x90000000\0" \ 51 "load_addr=0xa0000000\0" \ 52 "kernel_size=0x2800000\0" \ 53 "kernelheader_size=0x40000\0" \ 54 "bootm_size=0x10000000\0" \ 55 "console=ttyS0,115200\0" \ 56 BOOTENV \ 57 "boot_scripts=ls1012ardb_boot.scr\0" \ 58 "boot_script_hdr=hdr_ls1012ardb_bs.out\0" \ 59 "scan_dev_for_boot_part=" \ 60 "part list ${devtype} ${devnum} devplist; " \ 61 "env exists devplist || setenv devplist 1; " \ 62 "for distro_bootpart in ${devplist}; do " \ 63 "if fstype ${devtype} " \ 64 "${devnum}:${distro_bootpart} " \ 65 "bootfstype; then " \ 66 "run scan_dev_for_boot; " \ 67 "fi; " \ 68 "done\0" \ 69 "boot_a_script=" \ 70 "load ${devtype} ${devnum}:${distro_bootpart} " \ 71 "${scriptaddr} ${prefix}${script}; " \ 72 "env exists secureboot && load ${devtype} " \ 73 "${devnum}:${distro_bootpart} " \ 74 "${scripthdraddr} ${prefix}${boot_script_hdr}; " \ 75 "env exists secureboot " \ 76 "&& esbc_validate ${scripthdraddr};" \ 77 "source ${scriptaddr}\0" \ 78 "installer=load mmc 0:2 $load_addr " \ 79 "/flex_installer_arm64.itb; " \ 80 "bootm $load_addr#$board\0" \ 81 "qspi_bootcmd=echo Trying load from qspi..;" \ 82 "sf probe && sf read $load_addr " \ 83 "$kernel_addr $kernel_size; env exists secureboot " \ 84 "&& sf read $kernelheader_addr_r $kernelheader_addr " \ 85 "$kernelheader_size && esbc_validate ${kernelheader_addr_r}; " \ 86 "bootm $load_addr#$board\0" 87 88 #ifdef CONFIG_TFABOOT 89 #undef QSPI_NOR_BOOTCOMMAND 90 #define QSPI_NOR_BOOTCOMMAND "run distro_bootcmd; run qspi_bootcmd; "\ 91 "env exists secureboot && esbc_halt;" 92 #endif 93 94 #include <asm/fsl_secure_boot.h> 95 96 #endif /* __LS1012ARDB_H__ */ 97